Laguna Tools Industrial Dust Collector - I|Flux: 10 Elite
The iFlux|10 Elite has solved this issue by using an appropriate filter arrangement with 409 square feet of surface area – double that of a typical 10HP collector. To do this, we used a smaller diameter bag, and a lot more of them. This arrangement maximizes the amount of surface area possible which is vital to adequate airflow through the collector. Keeping these filters clean was addressed in the design. The positive pressure chamber pushes the air through the filters as the dust falls in the EZ Lift waste bins. As the dust cakes on, it will fall into the bin. A shaking mechanism has been added to help release the caked dust. The i|Flux Elite series has been tested in the assembly line, and it is ready for all fine dust applications.
Additional Details
Airflow 5000CFM @ 6”wc
The 15″ inlet has a net airflow of 5000CFM with a static pressure of 6″wc. A typical CNC Router needs a minimum requirement of 1500CFM, while a typical 37″ widebelt sander would call for a minimum 2000CFM. This makes the iFlux 10 a great fit for a CNC Router based cabinet shop that would be running several tools at once.
Fine Dust Ready
With fine dust, the key is to have a large filter surface area and to keep those filters clean. The smaller tube filter design of the iFlux|10 Elite are designed for the fine dust to cake on and the inner side of the filters and fall down into the bin as the mass grows. The filter surface area of the iFlux |10 Elite is 409 square feet. A typical 5HP dust collector has a surface area of 260 square feet. This increase in filter area translates to a large increase in airflow, making the iFlux an ideal machine for fine dust applications.
Quick Lever Wast Bins
The waste bins are easier to change than the kitchen garbage. Deactivate the air tight seal by pulling up the release bar and roll out the bin. The positive pressure design means there is no need for a bag hold down system like in multi-stage system. The wheels swivel 360 degrees and are mounted on a sturdy base to ensure they work in your shop for many many years.
Additional Features
The i|flux1 10 Elite fine dust collector displays an amperage read out on the control panel. This allows the user to monitor the efficiency of the motor. A high frequency remote is also included standard so that the operator can turn the machine on and off with a 60 meter range.
Safety
There are several NFPA standards in place to ensure the proper installation and use of a dust collector. For woodworkers, the standard is NFPA 664: Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking Facilities. The i|Flux 10 Elite complies directly with this standard. In addition, the i|Flux is fitted with a phase controller and TEFC motor for added electrical safety.
Features
- Motor HP: 10
- Motor RPM: 1720
- Air Flow: 5000CFM @ 6″wc
- Inlet Diameter: 15″
- Filter Area: 409 ft²
- Filter Bag: 40 x D168mm x H1800mm
- Filter Bag Material: Polyester
- Filter Cleaning: Manual Shaker
- Waste Bin: EZ Lift Metal Bin 64gal x 3
Specifications
- Power Requirements: 220V/ 60Hz/ 3Ph
- Amperage: 24.8 Amps
- Floor Space (W x L): 3424mm x 1140mm
- Machine Weight: 1069 lbs (485 kgs)
- Motor HP: 10
- Motor RPM: 1720
- Air Flow: 5000 CFM @ 6″wc
- Inlet Diameter: 15″
- Filter Area: 409 ft²
- Filter Bag (L x D x H): 40 x 168 x 1800mm
- Filter Bag Material: Polyester
- Filter Cleaning: Manual Shaker
- Waste Bin: EZ-Lift Metal Bin 64 Gal. x 3
- Shipping Weight: 1113 lbs
- Shipping Dimensions (L x W x H): 75″ x 39″ x 80″
WHICH LAGUNA CNC MACHINE IS RIGHT FOR YOU?
Woodworking CNC Machines
Industry-Leading woodworking machinery. Laguna CNC machines were designed & developed from extensive knowledge. Laguna Tools offers CNC Routers, CO2 Lasers, Edgebanders, CNC Turners & Joinery Machines, for your woodshop.
Laguna CNC machines work with the following materials: soft & hardwood, hard plastic, acrylic, non-ferrous metals such as aluminum, brass, copper, high-density foam & more.
Metalworking CNC Machines
Our state-of-the-art and easy-to-use metalworking CNC machines cut metal with ease and precision. Laguna offers an extensive line of Plasma Cutters, Fiber Lasers, Engravers & Metal Sanding Machines to fit any metal shop.
Laguna Metalworking CNC Machines work with ferrous metals such as iron, stainless steel, alloys, low medium & high carbon steel.
Multi-Tool CNC Machines
With spindles for routing & several knife cutting options, our Laguna Multi-Purpose CNC Machines work with a variety of materials from soft foam to hardwood. Ideal for any shop, our Multi-Tool CNC including the SmartShop 5-Axis Machine is hands down the best you can get.
Laguna Multi-Tool machines work with wood; plastic; vinyl; leather; fabric; soft, medium, and hard foam; as well as non-ferrous metals.
CNC Limited Warranty
New CNC machines sold by Laguna Tools carry a one-year warranty effective from the date of shipping. Laguna Tools guarantees all new machines sold to be free of manufacturers’ defective workmanship, parts, and materials. We will repair or replace without charge, any parts determined by Laguna Tools, Inc. to be a manufacturer’s defect.
- We require that the defective item/part is determined to be damaged due to lack of maintenance, cleaning, or misuse/abuse, the customer will be responsible for the cost to replace the item/part, plus all related shipping charges.
- This limited warranty does not apply to natural disasters, acts of terrorism, normal wear and tear, product failure due to lack of maintenance or cleaning, damage caused by accident, neglect, lack of or inadequate dust collection, misuse/abuse or damage caused where repair or alterations have been made or attempted by others.
- Laguna Tools, Inc. is not responsible for additional tools or modifications sold or performed (other than from/by Laguna Tools, Inc.) on any Laguna Tools, Inc. woodworking machine.
- Warranty may be voided upon the addition of such described tools and/or modifications, determined on a case-by-case basis.
- Software purchased through Laguna Tools, Inc., is not covered under this warranty and all technical support or licensing must be managed through the software provider.
- Normal user alignment, adjustment, tuning, and machine settings are not covered by this warranty. It is the responsibility of the user to understand basic woodworking machinery settings and procedures and to properly maintain the equipment in accordance with the standards provided by the manufacturer.
- Laguna Tools is not responsible for lost earnings due to a machine being inoperative or in need of repair.
- Spindles and bearings are not covered due to severe conditions or operating outside the duty cycle.
- Parts under warranty are shipped at Laguna Tools, Inc.’s cost either by common carrier, FedEx ground service or a similar method. Technical support to install replacement parts is primarily provided by phone, fax, e-mail, or Laguna Tools Customer Support Website.
- The labor required to install replacement parts is the responsibility of the user.
- Laguna Tools is not responsible for damage or loss caused by a freight company or other circumstances not in our control. All claims for loss or damaged goods must be notified to Laguna Tools within twenty-four hours of delivery.
Laser warranty exclusions:
- Damage to head, or Optic cable due to lack of volume or contaminated assist gas.
- Damage to components from misuse or lack of maintenance and cleaning.
- Operation of the machine by untrained employees.
- Operating the machine outside of its capabilities or beyond its duty cycle.
- Failure to use Distilled or deionized water will void warranty of power supply, chiller, and head.
- Optic failure due to back reflection errors will void power supply and Optic warranty.
- The machine must be kept and operated in a proper environment to maintain warranty.
CO2 Laser Warranty
- This warranty extends only to products distributed and/or sold by Laguna Tools to the original purchaser only.
- Any after-market additions or modifications will not be warranted. The laser machine system owner is responsible for any service and repairs outside the scope of this warranty
- This warranty covers only the normal use of the laser machine. Laguna Tools shall not be liable under this warranty if any damage or defect results from (i) *Irresponsible use, abuse, neglect, accidental damage, improper return shipping or installation (ii) Disasters such as fire, flood, lightning, or improper electric current (iii) Service or alteration by anyone other than an authorized Laguna Tools representative *Damages incurred through irresponsible use may include but are not limited to (i) Failure to turn ON or use clean water within the chiller (ii) Failure to clean optical mirrors and lenses (iii) Failure to clean or lube guide rails with lubricant oil (iv) Failure to remove or clean debris from collection tray (v) Failure to properly store the laser in a properly conditioned environment.
- Laguna Tools accepts no responsibility for any software programs, data, or information stored on any media or any parts of any products returned for repair to Laguna Tools.
- This warranty does not cover any third-party software or virus-related problems not purchased from Laguna Tools.
- Laguna Tools is not responsible for loss of data or time, even with hardware failure. Clients are responsible for backing up any data for their own protection. Laguna Tools is not responsible for any loss of work (“downtime”) caused by a product requiring service.
- Laguna Tools is a support-driven company. We continue to extend FREE tech support for life to the original clients. An annual fee will be charged to support resales (in the event the client resells the machine). The Warranty, however, is non-transferable.
- Laguna Tools agrees to absorb Ground Shipping Costs for Warranty Replacement Items. We offer the ability for clients to upgrade to expedited shipping for the cost difference, which will be invoiced and charged to the client prior to shipment.
- International shipping costs and/or customs fees associated with fulfillment of Warranty Replacement Items are the responsibility of the client.
- Laguna Tools at its own discretion reserves the right to deny the purchase of any extended warranty.
AFTER TWO-YEAR WARRANTY: POST WARRANTY SUPPORT AND/OR REPAIRS Laguna Tools offers free lifetime tech support via. phone and email to the original purchaser. However, after two (2) years replacement parts will be the responsibility of the client including shipping charges. Laguna Tools will provide a quote for the necessary parts and repairs.
Who is Laguna Tools?
We are the people we employ, the products we sell and the passion to serve our customers that emanates from both.
Laguna Tools was born in Laguna Beach, California in 1983, out of a desperate need to find safe, quality and precise woodworking machines for Torben Helshoj’s custom woodworking shop in Laguna Canyon. The tools that his partners used did not meet the high standards that Torben had used in Denmark, where he earned the Queen of Denmark’s Silver Medal in woodworking.
Armed with the experience from his four-year furniture making apprenticeship Torben returned to Europe with his business partners to purchase machines that would improve the quality of cuts and improve inefficiencies.
Laguna Tools forged a partnership with Robland Machines International to import high-end, superior quality woodworking machines and over the next decade the company became the number one importer of combination machinery in the US.
Now, over three decades later, Laguna Tools is still a corporation with the same values of quality, accuracy and safe products and that also focuses on their customers and their needs.
While we started off as a leader in the woodworking industry, we have now applied our innovative ideas to the metal, plastics, signs and composite businesses.
We do everything with one goal in mind — to help our customers build personal success stories.
We sell solutions.
Downloads
Automated Machines
iQ Series
Fiber Lasers
Specialty Machines
Swift Series
Plasma Series
CO2 Lasers
SmartShop®
CNC Turner Series
Industrial Machines
Bandsaws
Desktop CNC
Planers
Tablesaws
Metal Sanders
Wood Sanders
Dust Collectors
Shapers
Panelsaws
Jointers
Speciality Machines
SuperBrushes®
Classic Machines
Bandsaws
Lathes
Shapers
Tablesaws
Dust Collectors
Planers
Jointers
Sanders
Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.
Recently viewed
