Miller Millermatic 355 Pulsed MIG Welding Pkg w/Running Gear (951926)
The Miller Millermatic 355 Pulsed MIG welder is capable of single or three phase power, and carries a 60% duty cycle at 310 amp output. This welder will MIG and pulsed-MIG mild steel, aluminum or stainless from 22 gauge to 1/2 in. thick in a single pass. Advanced features make it easy for welders of any skill level to be productive and get great results.
Product Video
Features
Easy-to-understand interface: 7-inch color LCD display ensures proper machine setup and parameter selection, reducing setup time and increasing weld time.
Pulsed MIG welding delivers higher quality: Lower heat input for less distortion on thin materials, less spatter minimizes post weld grinding and rework allowing more welding time. Perform welding applications that couldn’t be done in the past.
Auto-Set Elite: Offers predefined weld settings to increase ease of use and ensure that the job is done right for operators of all skill levels.
Program mode allows easy save and recall of favorite weld settings.: Deliver more productivity, consistent quality by welders of all skill levels by using prequalified weld settings. Minimize supervisor need to intervene.
Auto-Line Technology: For portability and reliability this inverter power supply allows for any single-phase input voltage hookup (208–240 V) with no manual linking, providing convenience in any job setting. Ideal solution for dirty or unreliable power.
Versatility: Capabilities include MIG, pulsed MIG and flux-cored welding.
Portability - Machine only weighs 99 lb.: Weight is reduced by about 50 percent compared to the Millermatic 350.
Input voltage Selection Switch: The voltage switch is located in the wire drive compartment, for quick and easy voltage change. An error message will be displayed if the wrong input voltage is utlitized.
Optional EZ-Latch running gear: Operators no longer need to use lift truck to load machine and running gear into the truck. Latches secure machine to running gear. Simply loosen the latch retaining knob and rotate latches to disengage machine from running gear for easy portability.
Comes complete with: • Millermatic 355 power source • Single Cylinder Running Gear • Bernard BTB 15 ft (4.6 m) MIG gun (This MIG gun accepts Bernard Acculock S consumables) • 10 ft (3 m) Industrial power cord (without plug) for single- or three-phase • 10 ft (3 m) work cable with clamp • Factory-installed gas solenoid • Argon mix regulator/flow meter • .035/.045 in (0.9/1.2 mm) reversible V-groove drive rolls (order U-groove drive roll kits for aluminum welding) • Material Thickness Gauge • Chain to Secure Gas Cylinder
Aluminum 0.035 in. - 0.047 in. Aluminum 0.9 mm. - 1.2 mm. Metal-Core 1.2 mm. - 1.3 mm. Metal-Core 0.045 in. - 0.052 in. Stainless 0.023 in. - 0.045 in. Stainless 0.6 mm. - 1.2 mm. Solid Steel 0.9 mm. - 1.2 mm. Solid Steel 0.035 in. - 0.045 in. Flux Cored 0.035 in. - 0.045 in. Flux Cored 0.9 mm. - 1.2 mm. Silicon Bronze 0.030 in. - 0.035 in. Silicon Bronze 0.8 mm - 0.9 mm.
We recently purchased a saw and had a few issues. The bolts were missing, so we had to buy replacements from a local hardware store. Several other parts didn’t come in the shipment, and we ended up being charged extra to get them because they weren’t included in the original package. On top of that, the lead time was much longer than expected.
The one positive was the customer support team—email communication was excellent. They responded quickly and were helpful throughout the process.
What a nice piece of machinery. I’ve used a few times on both soft and hardwood. The finished product is smooth with very little sanding required. I’ve had a bit of snipe at the end of some longer boards but it’s negligible and to be honest it’s probably my lack of patience. Nice addition to my small hobby shop. Well worth the money.
bartell has to be the worst company to deal with, they do not have service manuals available on their website, service is not great. their equipment is not build to withstand construction applications. the manuals you can find are super cryptic and drawn out by a toddler. it's too bad i can't leave a lower score i feel like one star is still too good for them. get your stuff figured out guys, stop slapping your name on chinese garbage
Miller Millermatic 355 Pulsed MIG Welding Pkg w/Running Gear (951926)
The Miller Millermatic 355 Pulsed MIG welder is capable of single or three phase power, and carries a 60% duty cycle at 310 amp output. This welder will MIG and pulsed-MIG mild steel, aluminum or stainless from 22 gauge to 1/2 in. thick in a single pass. Advanced features make it easy for welders of any skill level to be productive and get great results.
Product Video
Features
Easy-to-understand interface: 7-inch color LCD display ensures proper machine setup and parameter selection, reducing setup time and increasing weld time.
Pulsed MIG welding delivers higher quality: Lower heat input for less distortion on thin materials, less spatter minimizes post weld grinding and rework allowing more welding time. Perform welding applications that couldn’t be done in the past.
Auto-Set Elite: Offers predefined weld settings to increase ease of use and ensure that the job is done right for operators of all skill levels.
Program mode allows easy save and recall of favorite weld settings.: Deliver more productivity, consistent quality by welders of all skill levels by using prequalified weld settings. Minimize supervisor need to intervene.
Auto-Line Technology: For portability and reliability this inverter power supply allows for any single-phase input voltage hookup (208–240 V) with no manual linking, providing convenience in any job setting. Ideal solution for dirty or unreliable power.
Versatility: Capabilities include MIG, pulsed MIG and flux-cored welding.
Portability - Machine only weighs 99 lb.: Weight is reduced by about 50 percent compared to the Millermatic 350.
Input voltage Selection Switch: The voltage switch is located in the wire drive compartment, for quick and easy voltage change. An error message will be displayed if the wrong input voltage is utlitized.
Optional EZ-Latch running gear: Operators no longer need to use lift truck to load machine and running gear into the truck. Latches secure machine to running gear. Simply loosen the latch retaining knob and rotate latches to disengage machine from running gear for easy portability.
Comes complete with: • Millermatic 355 power source • Single Cylinder Running Gear • Bernard BTB 15 ft (4.6 m) MIG gun (This MIG gun accepts Bernard Acculock S consumables) • 10 ft (3 m) Industrial power cord (without plug) for single- or three-phase • 10 ft (3 m) work cable with clamp • Factory-installed gas solenoid • Argon mix regulator/flow meter • .035/.045 in (0.9/1.2 mm) reversible V-groove drive rolls (order U-groove drive roll kits for aluminum welding) • Material Thickness Gauge • Chain to Secure Gas Cylinder
Aluminum 0.035 in. - 0.047 in. Aluminum 0.9 mm. - 1.2 mm. Metal-Core 1.2 mm. - 1.3 mm. Metal-Core 0.045 in. - 0.052 in. Stainless 0.023 in. - 0.045 in. Stainless 0.6 mm. - 1.2 mm. Solid Steel 0.9 mm. - 1.2 mm. Solid Steel 0.035 in. - 0.045 in. Flux Cored 0.035 in. - 0.045 in. Flux Cored 0.9 mm. - 1.2 mm. Silicon Bronze 0.030 in. - 0.035 in. Silicon Bronze 0.8 mm - 0.9 mm.
Here are are few more great reasons to buy from us:
Returns are easy, simplycontact usfor a returns number and send your item to our returns center for fast processing. We'll get you a replacement or refund in a snap! *Customer will be responsible for return shipping cost.
In the unlikely event that you find your item cheaper at another online store, just let us know and we'll beat the competitor's pricing hands-down.
We insist that you love everything you buy from us. If you're unhappy for any reason whatsoever, just let us know and we'll bend over backwards to make things right again.
Ordering from Landmark Tools is 100% safe and secureso you can rest easy. Your personal details are never shared, sold or rented to anyone either.
